diy ring pillow book

Laurie is always looking for ways to add a twist to the traditional. This week’s project is an alternative on a ring pillow. Instead of being tied on top, the rings are safely tucked away in a small well cut from the pages of the book. Ive attended a couple weddings where I’ve seen the little guys throwing the pillow around with the rings attached before they walk down the aisle, so having them enclosed in a book might be a great way to deter rings from flying everywhere too. Enjoy!

diy ring pillow examples

What you’ll need:
One small book (The book I used was roughly 4″ x 6″)
One length of wide ribbon (approximately 2.25 times the width of your book)
One length of narrow ribbon (approximately 4 times the width of your book)
One silk or ribbon flower
A scrap of decorative paper
Paper glue
Large square paper punch
A small, flat paint brush
A needle and thread.
Resources: Vintage Lily of the Valley Ribbon is from Nancy’s Sewing Basket,  Raspberry chiffon  grosgrain is from Midori.
diy wedding ring pillow
1.   Open your book to the second page.  Take your large square craft punch, turn it upside down (so you can see to guide and center it) and feed several of the right hand pages into the punch.   Slide it towards the middle of the book as far as you can go, keeping it vertically centered.  Squeeze the punch, and punch out the squares.    Important: Do not punch a hole in the first page of the book.
Remove the punch, feed the next few pages in , center again and punch out the squares.  Continue to punch out  squares until you’ve created a hole that is at least 3/4 of an inch deep.  (see figure 1)
2.  On the page after the last punched  page, glue down a scrap of  decorative paper  to line the bottom of  the “well” you just created.  (see figures 2 and 3)
3.  Center the wider ribbon on the spine of the book. Glue the tail of the wider ribbon inside the back cover  of the book.   Wrap the ribbon around the outsideof the book cover, and glue the other tail down inside the front cover.
Glue the first page of the book (the one without the hole punched in it) to the inside cover to secure and conceal the ribbon tail.    Glue the last page of the book to the inside of the back cover to secure the ribbon.       Allow to glue to dry.  ( see figure 4)
4.  Open the front cover of the book.   Use your brush to apply a generous coat of glue along the page edges on all three sides.   Allow the glue to dry, then give it a second coat.     Don’t close the book until it’s had a thorough chance to dry, otherwise, the “lid” could get stuck closed (see figure 5)
5.  Center your smaller ribbon on the spine of the book, in the middle of the wider ribbon, and tack it down using a couple of stitches with your needle and thread.     (see figure 6)
6.  Take your flower, and stitch it down to both layers of ribbon on the front cover of the book.   (see figure 7)
7.  Place your rings in the well and tie the ribbon tails into a bow to securely close box.   (see figure 8 and 9)
What it cost:
Book $8.00
Grosgrain ribbon – $1.75 a yard
Vintage Lily of the Valley ribbon  $7.50 for a half yard
Large square craft punch $13.00
Ribbon rose  (made with 1 yard of ribbon @ 3.99 a yard)
Project created by Laurie Cinotto


Comments (6)

Klub Diskon | Reply

great you creationc DIY RING PILLOW BOOK!

Featured Simple Bridal Portrait Session in the Mountains

This simple bridal portrait session in the mountains is made beautiful and amazing by many different factors, but our very favorite is the breathtaking location. Swap a city skyline for a mountain ridge, lake view, orchard, or garden and we'll take that any day!

Featured Minimalist Restaurant Wedding in Russia

Minimalist choices can still make for a stunning wedding!