Category: DIY Wedding Blog

Beautiful retro colored wedding cakes created by Chelsea of Cupcakes in Vancouver…

[Images c/o Jenn Ski]

I hope everyone had a fantastic weekend! It’s going to be an exciting and busy week for Once Wed so be prepared for 5 real weddings and lots of eye candy! We are guest blogging real weddings and diy projects all week on the wonderful Elizabeth Anne Designs, but will continue our regular posting on Once Wed too. Don’t forget to stop by EAD later on today to see more of this incredible chic and modern wedding….

Here are the rest of the pictures from EAD…for more information on projects and vendors…check out the feature on EAD

***The bride, Yvonne, is an incredible wedding photographer herself. Don’t forget to check our her lovely blog for more inspiration**

[Images c/o John and Joseph Photography]

How beautiful are these images from Julie Mikos breathaking wedding at Yosemite Valley? Don’t you just love her gorgeous bouquet and silver wedding dress….

[Photo's c/o Rebekah Silver]

Keeping with the same "twist on tradition" theme as last week……….Laurie‘s project today takes a unique twist on the traditional wish bowl with a stunning and clever "cake" box. Instead of guests dropping their wishes for the bride and groom in a bowl they drop them in a slot at the top of the cake, so the cake is functional and decorative at the same time. Laurie was generous enough to offer us two options on how to decorate the cake and I am loving both of them(especially the one above!). Over the next month we will feature instructions on how to create the caketopper and paper flowers too, but today’s post only contains instuctions on how to construct and decorate the box. If you are joining us for the first time from our feature on Brooklyn Bride(thanks, Vane!!), every Thursday Once Wed features a modern DIY wedding project created by Laurie Cinotto of lalalaurie. To see previous DIY wedding projects, click here. Thanks so much, Laurie!

Supplies:
Three round boxes (a small, medium and large)
One roll of paper gift wrap
Mod Podge Glue
Four yards of ribbon
An assortment of trims (artificial flowers, velvet leaves, etc)

Tools:
Small foam paint brush
Pencil
Ruler
Exacto Knife
Scissors
Glue Gun

Resources: Most craft stores carry all the supplies you need for this
project.

Directions:
Lay a sheet of your wrapping paper print side down. Place your boxes on
the paper (bottom side down) and trace around each box using a pencil.
(see figure one) Carefully cut out each circle.

Measure the height of each box, and cut a strip of paper as wide as the
height of your box and long enough to wrap completely around the
circumference.

Turn all three boxes over, so the bottom of box becomes the top of your
“cake tier”. You won’t be needing the lids to the two smaller boxes, just
the lid for the largest box which will be the bottom tier of your paper
cake.

Before you begin gluing, be sure to protect your work surface. Mod Podge
can be messy.

Apply an even layer of Mod Podge to the top of one your cake tiers using
a small sponge brush. (see figure two) Carefully place your paper
circle on the top of the box (in the glue) (see figure three). Smooth out
any air bubbles. Don’t worry about small wrinkles. They should
flatten out as the glue dries.

Glue the paper circles on the tops of the two remaining cake tiers.

Use the same gluing technique to adhere the paper to the sides of each
cake tier. As you wrap the paper around, it’s more important that the
paper lines up with the top of the tier rather than the bottom. The
bottom edge will be concealed with ribbon later.

When all three tiers are covered in paper, brush a thin layer of Mod Podge
on each tier’s papered surface. This will give the cake a subtle luster
and smooth down any edges you may have missed. If you would like a
richer surface, apply several coats of Mod Podge. Be sure allow at least
fifteen minutes for the Mod Podge to dry between coats.

On the top of the largest tier, as close as you can get to the edge, use
a Sharpie Marker to draw a “slot” large enough for a card to drop
through. (see figure four) CAREFULLY cut out the slot using an exacto
knife. It can be helpful to use a small metal cork-backed ruler as a
guide when you cut.

Decide how you would like to have each cake tier positioned, then use your
hot glue gun to glue them into place. ( Be very careful not to burn
yourself when handling your glue gun.)

At the bottom of each tier, wrap and glue down a length of ribbon. (see
figure five)

Glue a ribbon along the edge of bottom cake tier’s lid. This lid becomes
the bottom of your paper cake and makes the deposited cards accessible.

Decorate your cake ! (see figure six) Select your flowers, leaves and
trims, and use your hot glue gun to glue them into place. You can
place a traditional cake topper on the top of your cake, or create your
own.

As a variation on the idea, I collaged old book pages on the surface of
this cake. (see figure seven). You could decoupage anything. The sky’s
the limit!

In weeks to come, I’ll be giving instructions on the bird nest cake topper
and paper flowers too.

Budget:
3 paper boxes – $14
1 roll of wrapping paper – $4
4 yards of ribbon $10
Small bottle of Mod Podge $3
Trims and flowers $0 (Use up those little bits of this and that you’ve
got stashed in your crafting supplies)
Total Cost – $31

Adorable Jen Murphy caketoppers are now available in her new etsy shop. The yellow chicks in the middle are too cute!!

[Photos c/o Jen Murphy via Erica at Thoughtful Day]